Toilet Repair

How To Keep Your Toilet Free From Leaking

Toilet Repair toilet leak, toilet leaking

Leaking toilet tanks are responsible for the loss of tens of thousands of gallons of water per year. That isn’t good for the environment, and it isn’t good for your wallet either. Toilet tanks aren’t infallible; after you’ve had them for a few years, it is not unusual for a leak to start. As a result, it is important to take a look at your plumbing system on a regular basis to make sure there aren’t any issues.

toilet leak

How To Stop A Toilet Tank From Leaking

The best way to prevent a problem is to periodically look over your toilet tank and make sure there are no leaks. Most toilets and tanks are very similar. There are two valves in the tank. One is a flush. The other collects the water until it is ready to be flushed. The ball-cock is a refill valve that is often found in the toilet tank. If the flush valve doesn’t seat right, there is an issue with your tank and it is time to call in a professional.

When a leak springs up, tank water gets into the bowl. If left unchecked, the refill tank continues to fill up, over and over. That means there is a lot of water that gets wasted. It is also possible for the refill valve to leak as well. Water is constantly moving into the bowl. That should alert you to the fact that there is a major problem.

Detecting The Source of the Toilet Leak

Figuring out if the flush is leaking is not hard. Once you determine that there is a leak, stop the water supply so that the toilet tank is not getting any water. There is a valve that does this. One thing you can do is to note the water level once you have closed the water. Wait half an hour and then look to see if there is any difference. Obviously, if there is not as much water as before, there is a leak that needs to be addressed.

However, if the water is at the same level, there is no issue with the flush valve. The problem is the refill valve instead. The fix for that is pretty simple; just tighten it up a little or adjust a few things. You also need to check to see that there is ample water for flushing but nothing else. You don’t want the water to move over the overflow pipe.

There is a water level mark in every flush tank. You do not want the water level to be too low. The water is necessary for there to be a sealing trap. Occasionally, the float may come in contact with other parts of the toilet. To stop that from happening, just separate the float and the leak should stop.

You need to make sure there isn’t any water logging, either. Fix this issue by taking the float out and washing it off. If logging continues to be a problem, get a new part. If you are also struggling with the flush valve, and nothing you do is making a difference, put in a new flush ball. Just the actuating mechanism can be switched up as well, so you may not have to replace the entire part. Before you buy something new, though, check to make sure there isn’t anything you can do that will fix the problem.

If the idea of your toilet leaking makes you anxious then you can reach out to us for a local plumber who has all the tools and experience needed to solve your plumbing issue quickly.

How To Prevent Clogs And Keep Your Toilet In Good Working Order

Toilet Repair Clogged Toilet, toilet clog

When your toilet is clogged, the situation can become dire. You definitely want to make sure it is running seamlessly so you don’t have a nasty cleaning project on your hands. In addition, if you ignore a plumbing problem, it can get quite expensive over time.

toilet clog

1) Perform Random Inspections

Regular maintenance is essential if you want to keep your toilet in good working order. Look to see if it is filling and draining properly. Make sure there isn’t any rust or corrosion. In addition, examine your floating bar to make sure it is straight. Double check that your water connection is secure. Put the handle on “open” unless water starts to rise too high as a result of an overflow.

2)Don’t Let Water Run

If you notice that your water is running, take care of the situation right away. A little leak can turn into a huge problem very quickly. Not only is it a hassle to deal with at that point, but it also costs a lot of money. Look at your connections and check to see that the tank is functioning properly. Take a look at the shut off switch to ensure there isn’t any rust or leakage.

Toilet clogs can pop up without much warning, call us to ensure that you don’t have to deal with one in the future.

3) Only Put Toilet Paper In The Toilet

Toilet paper can obviously be flushed down the toilet. There are also flushable wipes that work well, too. However, some people also try and flush other items, like tampons, paper towels and even q-tips. You should never put anything like that in the toilet; it belongs in the trash instead. If you do flush them, you risk clogging up the toilet, and you will have to hire a professional to fix the issue.

4) Avoid Chemical Drain Cleaners

When you have a clog, your initial inclination may be to use a chemical drain cleaner. Don’t do that. Chemicals can create an even bigger problem than you already have, and they can also cause issues for your plumbing system.

5) Flanges Are Your Friend

A run of the mill plunger just does not do the trick any more. Instead, look for something that has a flange as well; they do a better job at getting rid of tricky toilet clogs. The flange works to get a good seal, so there is much more suction when you are using the plunger. If you try to use anything different, you may wind up making a big mess and will still not see the results that you want. Make it easy on yourself by purchasing a bulb shaped plunger with a flange.

5 Most Common Toilet Issues | How to Fix Those Common Issues

Toilet Repair Clogged Toilet, Toilet Issues, toilet problem

A clogged toilet is frustrating and potentially dangerous. In order for your toilet to work properly, you will need to clear the clog. The following toilet repair tips can help you out if you find yourself dealing with a clogged toilet.

clogged toilet

Recurring Clogs

One of the most common problems with toilets is clogs. A toilet that is used and flushed often is at risk of developing a clog. If your toilet does not flush properly, it can be either partially or completely clogged.

When a toilet is completely clogged, it will fill to the brim or overflow. A partial clog can cause the toilet to slowly drain. With this type of clog, waste cannot be flushed; however, the water in the bowl slowly decreases over time. There are several tools that can help to remove a clog. With practice, you can get a toilet unclogged.

Clearing Clogs with a Plunger

Most clogs can be cleared using a plunger. It is important to remember that unclogging a toilet can be a dirty job. So, wear protective clothing and gloves. To clear a clog using a plunger, place the plunger in the bowl and make sure there is enough water to completely cover the plunger.

The first plunge should be done gently as a hard plunge can cause water to splash all over you and the bathroom. After the first plunge, you should force the plunger up and down vigorously to help remove the clog.

Snake It Out

If you cannot clear the clog with a plunger, you should use a plumbing snake. A plumbing snake is a flexible wire coil that has a corkscrew on the tip. The snake can be threaded through your pipe to the clog. As you turn the snake, it digs its way through the clog using a boring action. Most of the time, a plumbing snake will be able to clear a clogged toilet.

Phantom Flushes

Does your toilet refill intermittently, even though it has not been used? If so this is called a phantom flush. Ignoring phantom flushes can waste more than 200 gallons of water daily. This problem is due to water leaking from the tank, causing it to refill. This is often due to a faulty flapper or flapper seat.

To fix this, you will need to drain the water from the tank and the bowl and turn off the water supply. Inspect the flapper for wear or damage. If the flapper shows any signs of wear or damage, it will need to be replaced. This is a simple repair that most homeowners can handle themselves.

5)Broken Toilet Handle

A broken toilet handle can be frustrating; however, it is an easy fix. To fix a loose or stuck toilet handle, you will need to remove the tank cover and clean the mounting nut.

Typically, debris will cause the handle to stick. Cleaning it should correct the problem. If the toilet handle is loose, try turning the nut clockwise to tighten. These two steps typically will fix any toilet handle issues.

When To Call For Plumbing Service?

There may be times when there is more going on than a clogged toilet, a worn flapper or a loose toilet handle. In these cases, you will need to contact a licensed plumber.

An experienced plumber has the skills necessary to diagnose your toilet problems and solve them. If you are unable to fix the issue yourself, a plumber can fix your toilet so that it is running like new.

When you contact a plumber, you want one who has the experience and skill needed to handle all of your plumbing issues. We are offering best quality plumbing service in Memphis.

Is Your Toilet Hissing? Reasons For It And How To Prevent It

Toilet Repair toilet clog, Toilet Hissing, toilet repair

toilet hissing

If your toilet makes a hissing noise, it means you likely have one of the following problems:

Debris that is stuck in the fill valve
A broken float

We will explain these two problems, why they create your toilet’s hissing sound, and what to do about it.

If you need a Plumber to fix your toilets hissing sound immediately, call us and we will send a plumber out to you.

Debris Stuck In The Fill Valve

The fill valve is a part that is near the left side of your toilet tank. The valve works to fill the toilet tank with water after each flush. When it works properly, the fill valve will shut off as soon as the water in the tank reaches a certain level.

The fill valve can stop working right if debris gets caught in it. The debris will keep the valve from closing correctly. It also pushes rough a restricted opening and that causes the hissing noise

To fix the issue, remove the valve and let any dirt get flushed out of it. If you notice that it is broken, follow the steps in the video below to replace it. If you cannot do this yourself hire a plumber to flush any sediment out of the fill valve.

24 Hour Toilet Repair In Memphis

The Damaged Float

The toilet’s float indicates to the valve when it is time to turn on or off. It does this by going up and down. After the toilet gets flushed, the float raises upward and lets the fill valve go on. Once the float goes back to the correct level, it causes the fill valve to shut the water off.

Floats sometimes look like black or red balls or balloons. Older toilets have a long metal arm connected to the float. Newer toilets have a similar structure but may have a flap type of cover rather than a round one.

There are times where certain problems prevent the float from getting high enough to shut the fill valve all the way off. As water tries to escape, the pressure builds inside the valve trying to escape a small opening, which then creates a hissing noise.

Some of the problems that can prevent a float from shutting off include:

Water getting into the float thereby affecting its buoyancy
Debris blocking the float’s movement upwards

How To Detect A Silent Toilet Leak

Toilet Repair running toilet, toilet leak

Your plumbing system is one of the most important systems in your home. If you do not keep it properly maintained, a number of issues can arise and cause you problems. One of the most annoying issues of a plumbing system is a leaking toilet.

toilet clog

A leak increases your water consumption, thus increasing your water bill. Some typical sounds associated with a silent leak are sounds coming from the toilet when it is not being used, needing to keep the handle pressed down to completely empty the tank, water that runs down the sides of a toilet when it is not being flushed and runs even when the handle has not been pressed down. These can point towards a leak; however, you may have a leak even if you cannot hear it or see it. This type of leak is called a silent toilet leak. In order to diagnose this type of leak, you will need to perform one of the following tests.

The Dye Test

This test is very popular among homeowners. To perform this test, you will need to purchase a dye kit from your local plumbing supplier or your water company. The dye supplied is typically red in color. Once the dye has been purchased, you are ready to begin the leak test.

Remove the water tank cover and any product that colors the water, such as a toilet cleaning tablet. In order to do this test, you will need completely clear water. Next, place enough dye in the tank to create a deep red color. Wait thirty minutes and verify if the water changed color. If the water has turned even a light pinkish color, you have a silent leak.

Shut Off the Water to the Toilet

Another way to determine if you have a silent leak is to turn off the water to
the toilet at bedtime.

In the morning, check the water level in the tank. If there is less water in the tank than there was when you went to bed, you have a silent toilet leak.

Toilet leaks can cause you to waste a lot of water. In fact, some homeowners lose as much as 500 gallons of water each day due to a leaky toilet. This not only increases your water bill but also is not good for the environment. There are several reasons for a leaky toilet, including a worn out ball or flapper, a crack or hole in the overflow tube, the gasket under the flush valve is damaged or a new washer or seat is needed for the ballcock.

Because silent leaks cannot be heard or seen, many homeowners do not know they have a leak until they get a huge water bill or experience a serious plumbing issue. One of the most important maintenance tests that a homeowner can perform is a silent leak test using one of the methods described above.

Performing this test will ensure that your toilet is running properly, improve your water conservation efforts and keep your water bills low. Still if you find any other problem don’t forget to contact our Plumbing Service for any kind of plumbing service.

Toilet Problems That Need To Be Repaired By A Professional

Toilet Repair toilet leak, toilet problem, toilet repair

If you aren’t already familiar with the inner workings of your toilet, it is worth learning more about how the flushing process works. Once you understand how the components in the toilet tank work, you will be in a much better position to identify toilet-related problems.

toilet problems

The best way to learn more about your toilet is by watching it in action. Begin by removing the lid from the back of the toilet tank. Then, flush the toilet. As you do, you will see that the toilet handle is attached to a chain that lifts up a flapper valve. This opens the flush valve opening, allowing water to drop down from the tank into the bowl.

As the new water enters the toilet bowl, the dirty water and the waste is forced down the drain pipe. Once all of the water has been removed from the tank, the flapper valve drops back into position, blocking the exit and allowing the tank to fill up again. Once the float ball reaches the correct height in the tank, the water shuts off.

After seeing all of these steps in action, it will be easier for you to identify problems so that you can have them repaired.

Toilet Problems That Need Plumbing Repair

A Bad Flapper Valve

If the flapper valve on a toilet becomes cracked or gets too brittle over time, it will no longer seat properly around the opening in the bottom of the tank. As a result, water can continuously seep down from the tank into the bowl, causing the toilet to run all of the time. Another common symptom of this problem is if it sounds like there is a pipe banging when the toilet finishes filling. This is an easy repair that our experts will be more than happy to help you make.

Upgrading Your Existing Toilet

If you have a standard toilet in your home, you may want to consider upgrading it to a larger model. Bigger toilets are generally more comfortable to use. Although it may not seem like comfort should be a big factor when choosing a toilet, it is actually an important consideration. If you are ready to make a positive change, contact us today so that we can help you find a toilet that is sized properly for your needs.

Other Toilet Issues That Require a Plumber To Repair

Some of the other toilet problems that can occur that require professional assistance include the following:

Leaking water
Cracks in the tank of the toilet
Pools of water around the base of the toilet
Problems flushing the toilet
A handle that is stuck or that is too loose

4 Tips For How You Can Keep Your Toilets From Clogging

Toilet Repair Clogged toilets

Clogged toilets are noted as being one of the most common residential plumbing problems.

Whether it is jewelry or rolled up toilet paper, the toilet can clog up in seconds and become impossible to correct. As a result, it’s important to understand what can be done to make sure it’s properly taken care of.

clogged toilet

Here are a few tips to keep in mind when preventing a toilet from clogging:

1) Set a Scheduled Maintenance Routine

Maintenance is a must whether it has to do with smaller components or how the toilet is functioning. Each part plays a role in the toilet’s ability to function properly.

This is why it’s important to go through a comprehensive maintenance routine twice a year. This semi-annual approach can help alleviate clogged toilets over the long-term.

Any issue that does arise will be taken care of during the scheduled maintenance routine. For those willing to spend a bit of money, it’s highly recommended to seek out a qualified plumbing company for these scheduled check-ups.

2) Don’t Use Chemicals

Chemicals are horrible for the toilet and can do a tremendous amount of damage to the toilet’s structural integrity.

It may seem like a good idea to use chemicals while cleaning the toilet but they do more harm than good. It’s all about keeping the cleaning process as natural as possible to avoid filling the toilet is bad chemicals. These chemicals can start to build up inside the pipes and eventually clog up the toilet.

It’s better to avoid chemicals and only use natural cleaning methods such as a plunger.

This will ensure the pipes remain clear throughout the year.

3) Only Flush Human Waste and Toilet Paper

Stuffing random items into the toilet and flushing them is a bad idea. This is what ends up costing property owners. It’s important to not only avoid doing this as an adult but to also make sure younger children are aware of these rules. They shouldn’t be tossing small toys into the toilet and flushing them.

This is one of the fastest ways to clog the toilet.

It’s a good habit to make sure only human waste and small amounts of toilet paper are flushed (don’t roll up the tissue paper into a large ball!). Anything other than shouldn’t be going into a toilet bowl.

4) Purchase a Good Plunger

Sometimes, the issue has more to do with not having the right plumbing tools.

There are situations where a property owner may ignore a problem because they don’t own a plunger. It’s better to go out and invest in one as soon as possible. This will make it easier to take care of minor problems before they turn into larger ones. In many cases, quick action can go a long way in keeping the toilet in good shape.

These are the tips to implement as soon as possible when it comes to keeping the toilet in good shape.

There is no reason to see it get clogged as long as the right steps are taken.

What To Do When You Have A Clogged Toilet

Toilet Repair Clogged Toilet

While a toilet is a very important part of a home or commercial premises, we only think about it when it has a problem. One of the major toilet problems is a clogged toilet. This problem is very common and it is good to know how to deal with it. You don’t have to call a plumber whenever you face a toilet clog. You can deal with a simple clog all by yourself.

Here are some of the things you can do when you face a simple toilet clog:

Use a Plunger

Using a plunger is one of the most effective ways to fix a simple toilet clog. Most of the homeowners and business owners usually have a plunger on hand to fix a toilet clog. Put the plunger into the toilet bowl and once you have ensured that the hole is completely sealed and covered, push the plunger down in a gentle way. Maintain the seal and push the plunger a bit more forcefully up and down and pull the plunger away to break the seal. If the water rushes down, it means that you have fixed the toilet clog.

Use Vinegar and Baking Soda

Vinegar and baking soda are very important household items as they can be used to remove stains and sanitize countertops and to unclog a toilet. To use vinegar and baking soda to fix a clog, pour 1 cup of baking soda into the toilet bowl you want to unclog.

Next, wait for a few minutes so that the baking soda can fully disperse. Once these minutes are up, pour 2 cups of white vinegar and allow bubbles to form. Finally, leave the mixture for many minutes and then check to see whether or not it has fixed the problem.

Hot Water and Dish Soap

Using hot water and dish soap to unclog a toilet may be a good option if you don’t have baking soda, a plunger, or vinegar. Heat a gallon of water on the stove. Ensure that it is very hot but does not boil. While the water is still heating, use a generous amount of dish soap in the toilet bowl water. Once the water is hot, pour it into the soapy bowl and leave it for several minutes so that the mixture can take effect.

Call a Local Plumber To Fix Your Toilet.

If You Are Having An Issue With Your Toilet, Call Us Today

Even though at-home remedies can fix simpler toilet clogs, it cannot fix all toilet clogs. Look for a professional if your toilet clog is caused by a foreign object, is stubborn, or causes your toilet to overflow. A professional plumber can fix a toilet clog without causing any damage to your plumbing system. You can contact our Plumbing Service for professional plumbing service in Memphis Area.

6 Reasons Why Your Toilets Get Clogged Often

Toilet Repair Toilet Blockages, toilet clog

Clogged toilets can happen in any home to anyone. When this type of situation occurs, most people choose to contact a plumbing professional to assist them with the issue and ultimately remove the blockage so they can get back to using their toilet the way that they normally would.

Some people are more concerned with solving the problem quickly than figuring out why the toilets keep on getting clogged. However, it’s certainly important to understand what generally causes these clogs to happen.

plumber fixing toilet

Here Are Some Main Causes of Toilet Blockages:

Too Much Toilet Paper

It’s normal to flush toilet paper down the toilet. After all, it’s what most people use to wipe themselves when they’re finished using the bathroom. However, putting too much toilet paper into the toilet at once could cause a major clog to occur.

It’s best to limit yourself on the amount of toilet paper you’re flushing down the toilet. Some people even prefer to fold their sheets of toilet paper and throw them away in a trash bin instead of flushing them down just to avoid the possibility of dealing with a clogged toilet in the future.

Not Enough Water

You should have enough water in your toilet to flush when you use the bathroom. If there isn’t enough water, you may notice that not everything goes down when you flush the toilet. And, if everything isn’t going down at once like it should, the issue could eventually lead to a clogged toilet that you’re stuck trying to fix.

Check the water supply to determine how much water you have. Make sure that you have enough water in your toilet before you start using it again.

Too Much Hard Water

There are many people who have hard water in their homes, but this hard water can eventually lead to deposits of the minerals throughout the pipes. As a result, it’ll take its toll on the way your toilet flushes, causing a bit of a blockage. If you’re dealing with this kind of problem, you’ll need to use a solution designed to treat that mineral buildup and keep it from happening again.

Flushing Foreign Objects

You should never flush any foreign objects down your toilet. The toilet is meant for waste and the usual amount of toilet paper a person uses when they’ve urinated or taken a bowel movement. Unfortunately, some people end up flushing other objects down the toilet, including paper, food, and even small toys. These items could lead to a serious blockage that keeps your toilet from flushing properly.

Drain Line Blockage

One of the most common causes of a clogged toilet is a drain line blockage. If there’s a blockage, the toilet tank isn’t going to start filling up with the right amount of water and then you won’t even be able to flush the toilet when you use it.

Grease in the Pipes

Do you normally throw grease down the drain of your kitchen sink? You may think that it has absolutely nothing to do with the toilet at all, but that’s not exactly true. Whenever grease is poured down the drains, it makes the pipes harder, and it’ll be more of a challenge for water to reach your toilet. And, as you may have already learned, a lack of water will keep your toilet from flushing properly.

The best way to avoid this situation is to put grease in a glass container and dispose of it another way. It’s simply not a good idea to let it flow down the drain inside of the kitchen sink.

These are some of the many causes of clogged toilets. It helps to know this information in advance in case you find yourself dealing with a clogged toilet in the near future. It may cost you more to treat the problem with your toilet, so why not do your best at preventing problems from taking place? A professional plumber could help to perform routine maintenance in your home to keep things in working order, too. Contact Plumbing Emergency Memphis for any kind of plumbing service in Memphis.

Fixing a Running Toilet

Toilet Repair running toilet, toilet repair

If your toilet is running all of the time, then your stress levels are likely rising every time you hear or see it. Just the sounds of a toilet running constantly can make you pull out your hair. On top of the never-ending noise, your brain keeps reminding you of the money that’s getting wasted along with the water. No homeowner can be happy with a running toilet.

Fortunately, this is something that even basic DIY homeowners can handle. You just to be somewhat patient and know a few helpful hints, which are offered to you here if you keep reading.

Is Your Toilet Running Constantly? Learn What You Can Do About This!

Fix Your Flapper

Not sure what the flapper is? It’s the specific piece that controls water flow both on and off anytime the toilet gets flushed. One possible issue is when the flapper gets stuck open. Another possible source of your difficulty is when a flapper gets cracked or has a broken seal. In any of these circumstances, water is going to keep flowing into your toilet bowl, even at times that it’s not supposed to do so.

Watch your flapper when you flush your toilet to see if it winds up sticking opening. Make the necessary adjustments. To determine if a replacement is necessary, try pressing down on it as you flush. If this additional pressure is able to stop the flow, it’s time to put a new flapper in. Most of the time, when you buy a new piece, it will come with installation instructions.

Issues With The Fill Height

Something else you can try is adjusting the fill height. There’s a line inside your toilet that should indicate where the water is going to fill up to. To begin, be sure that your fill valve is properly on. The next step is checking your float height. Your toilet might have its own ball float. If you want to adjust the height of it, then it should be possible to bend its arm so the float adapts to the position that you need for it to be.

If your toilet instead has a cup-type float, then getting the float to an appropriate level means moving the spring-clip fasteners. That ought to deal with the toilet running constantly. If it hasn’t, then keep moving down the list of possible problems.

Fix Your Toilet’s Fill Tube

When your toilet tank is filling up, water will flow from its fill valve and through its fill tube into its overflow tube. Your toilet’s fill tube is what helps manage the water flow, as it directs any excess water to get siphoned off into the overflow tube.

Water isn’t going to flow through appropriately if that tube gets cracked in any way. Also, the tube won’t even work if its end gets submerged under water.

If you want to fix your fill tube, you might just have to cut back some of the tubing. On the other hand, if there’s an actual crack, then you have to replace the tube with a new piece.

Call a Plumber To Repair Your Toilet

Plumbing issues of all sorts can be huge problems for a homeowner. We take pride in helping you immediately when needed, and you get the peace of mind of knowing your home’s plumbing is in the capable and professional hands of a local plumbing services company.

Call us right away to schedule your service or get help with a plumbing emergency.